These comments were sent in by Kate Sharp and I thought they would be useful not only to me but to others too.
Day 1
I haven't encountered joins on the second half of a split ring and although I managed to keep the ring sliding, the picot is twisted so I probably need some extra tuition on how to resolve this.
2nd Part I've done it and it works! I don't think I've done split ring in and out of a flower to travel along in a line, so it was a good experiment! Turning ove the work and reversing the stitch order is also new but I reprogrammed my brain and achieved it. Didn't quite pull the two upside down rings (10 and 11) fully closed. Last two stitches in each ring seem to ping the other way a little, probably because the stitches and ring are a little loose. Good intro to the technique though! Very clear notation and good corresponding diagram.
Day 3 Still struggling with twisted last two stitches of opposite way round ring, and joining to second half of split ring, but I've done it. How much is 1/8 inch?! No guesses as to what it will become!
Day 4 and 5 Forgot to do the 'front side back side' tatting technique for the tiny ring 21 in part 4 but as its so small it doesn't show too much. Tied on a new shuttle as ran out the two yards I'd put on working shuttled to start with. It seems to be a nicely spaced pattern without straining to join up. Got fractionally confused as to which shuttle I was on but found that it all made sense if I just went with it! Still no idea what the motif is!
Days 6 and 7 Still going well and the notation is clear to follow. I find it much easier having instructions and a diagram for reference rather than a diagram bespeckled with numbers. My joins on the second half of a split ring are neater and becoming easier to work, although they still don't always look quite right. The front side/back side tatting is clever and impressive! I am pleased at how stable the piece is. I think I might be tatting a little pig! Its tail went a bit short though. I wondered if the circles bouncing along its back might make it a woolly sheep, but I think its legs look more pig-like. I hope it will be cute! I have found it most intruiging to witness the construction of the design and where uneven split rings end up!
Day 8 Got a bit confused about which shuttle to start with, so had to unpick a giraffe neck I'd made! Forgot front-side-back-side tatting for the second chain of block tatting, but never mind! The block tatting is fine though, not something I'd done before but the instructions were nice and clear. Wound another two yards onto the second shuttle as I'd run out the two yards that were already on there. I reckon it's going to be a hippo now.
Days 9 and 10 I have tatted a hippo! The lock stitch seemed to go fine - so many reversals and different stitch combinations that I haven't tried before! The eye bead went on very well - before when I've tried this it's twisted and not worked very well, so I was pleased about that!
I had expected him to have an open mouth with two little rows of teeth - maybe this could be an adaptation! I also think he looks a bit rhino-shaped so maybe another version could have a horn! I was pleased to see he looked like the picture!
In my experience, the 'main' working shuttle needs about 3 1/2 - 4 yards and the secondary one about 2 1/2 - 3 yards - if I'd put this much thread on at the start I'd have had less ends to finish when I'd completed it so I think a thread estimate would be a useful addition to any similar future project. The process has been fun and I've looked forward to the instalments, which were in very achievable sized chunks. I have learnt a lot about the construction of a tatted animal and I think his feet are really cute! Thanks Jane!
Day 1
I haven't encountered joins on the second half of a split ring and although I managed to keep the ring sliding, the picot is twisted so I probably need some extra tuition on how to resolve this.
2nd Part I've done it and it works! I don't think I've done split ring in and out of a flower to travel along in a line, so it was a good experiment! Turning ove the work and reversing the stitch order is also new but I reprogrammed my brain and achieved it. Didn't quite pull the two upside down rings (10 and 11) fully closed. Last two stitches in each ring seem to ping the other way a little, probably because the stitches and ring are a little loose. Good intro to the technique though! Very clear notation and good corresponding diagram.
Day 3 Still struggling with twisted last two stitches of opposite way round ring, and joining to second half of split ring, but I've done it. How much is 1/8 inch?! No guesses as to what it will become!
Day 4 and 5 Forgot to do the 'front side back side' tatting technique for the tiny ring 21 in part 4 but as its so small it doesn't show too much. Tied on a new shuttle as ran out the two yards I'd put on working shuttled to start with. It seems to be a nicely spaced pattern without straining to join up. Got fractionally confused as to which shuttle I was on but found that it all made sense if I just went with it! Still no idea what the motif is!
Days 6 and 7 Still going well and the notation is clear to follow. I find it much easier having instructions and a diagram for reference rather than a diagram bespeckled with numbers. My joins on the second half of a split ring are neater and becoming easier to work, although they still don't always look quite right. The front side/back side tatting is clever and impressive! I am pleased at how stable the piece is. I think I might be tatting a little pig! Its tail went a bit short though. I wondered if the circles bouncing along its back might make it a woolly sheep, but I think its legs look more pig-like. I hope it will be cute! I have found it most intruiging to witness the construction of the design and where uneven split rings end up!
Day 8 Got a bit confused about which shuttle to start with, so had to unpick a giraffe neck I'd made! Forgot front-side-back-side tatting for the second chain of block tatting, but never mind! The block tatting is fine though, not something I'd done before but the instructions were nice and clear. Wound another two yards onto the second shuttle as I'd run out the two yards that were already on there. I reckon it's going to be a hippo now.
Days 9 and 10 I have tatted a hippo! The lock stitch seemed to go fine - so many reversals and different stitch combinations that I haven't tried before! The eye bead went on very well - before when I've tried this it's twisted and not worked very well, so I was pleased about that!
I had expected him to have an open mouth with two little rows of teeth - maybe this could be an adaptation! I also think he looks a bit rhino-shaped so maybe another version could have a horn! I was pleased to see he looked like the picture!
In my experience, the 'main' working shuttle needs about 3 1/2 - 4 yards and the secondary one about 2 1/2 - 3 yards - if I'd put this much thread on at the start I'd have had less ends to finish when I'd completed it so I think a thread estimate would be a useful addition to any similar future project. The process has been fun and I've looked forward to the instalments, which were in very achievable sized chunks. I have learnt a lot about the construction of a tatted animal and I think his feet are really cute! Thanks Jane!
No comments:
Post a Comment